Easy user Interface.The signal from the RF AMP (IC18) is applied to the 1st IF circuits. Program frequencies in a friendly and versatile spreadsheet type interface. GENERAL: PC Programming Software for the ICOM type IC-R6. Compatible for Windows 98 / ME / 2000 / XP Vista / 7. Program Frequencies in a friendly and versatile spreadsheet type interface. PC Programming Software for the ICOM type IC-R6.
No risk of personal injury, fire or electric shock.Icom, Icom Inc. Many hours of research and development went into the design of your IC-R6.D FEATURESm Covers 0.1001309.995 MHz* wideFrequency range * Some frequency bands are prohibited, depending on theM External power supply operationm 1300 memory channels with 22 banksAvailablem 150 mW* AF power with BTL (bridge-tiedLoad) amplifier *At 10% distortion with a 16 load (internal speaker)IMPORTANTREAD ALL INSTRUCTIONS carefully and completely before using the receiver.SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC-R6.R DANGER!Personal death, serious injury or an explosion may occur.R WARNING!Personal injury, fire hazard or electric shock may occur.NOTE Recommended for optimum use. With proper care, this product should provide you with years of trouble-free operation.We want to take a moment of your time to thank you for mak-ing your IC-R6 your radio of choice, and hope you agree with Icoms philosophy of technology first. The IC-R6 communications receiver is designed and built with Icoms superior technology and craftsmanship. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.FOREWORDThank you for purchasing this Icom product. When using the connected earphone as an.This device complies with Part 15 of the FCC Rules.
Otherwise, the installed batteries will become exhausted, and will need to be recharged.FCC INFORMATION FOR CLASS B UNINTENTIONAL RADIATORS:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Remove batteries from the receiver when not using it for a long time. This may damage the bat-tery.DO NOT use or place the receiver in direct sunlight or in areas with temperatures below 10C (+14F) or above +60C (+140F).DO NOT use harsh solvents such as benzine or alco-hol to clean the receiver, because they can damage the receivers surfaces.Even when the receiver power is OFF, a slight current still flows in the circuits. This may result in an electric shock or damage the receiver.NEVER solder the battery cell.
Easy To Use For Icom Ic-R6 Code Setting 41
Its a good idea to clean the battery terminals once a week.D Belt clipConveniently attaches to your belt.To attach the belt clip:Slide the belt clip into the plastic loop on the back of the receiver. (See page I I fo r charg ing instructions.)Keep the battery terminals clean. Be sure to observe theTeries before use. AF energy is in the range of 20 to 20,000 Hz.* kHz is an abbreviation of kilohertz or 1000 hertz, MHz is abbrevi-ation of megahertz or 1,000,000 hertz, where hertz is a unit of fre-quency.OPERATING NOTESThe IC-R6 may receive its own oscillated frequency, result-ing in no reception or only noise reception, on some fre-quencies.The IC-R6 may receive interference from extremely strong signals on different frequencies or when using an external high-gain antenna.CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this device under FCC regulations.TABLE OF CONTENTSFOREWORD iIMPORTANT iEXPLICIT DEFINITIONS iPRECAUTIONS iiFCC INFORMATION iiiOPERATING THEORY iiiOPERATING NOTES iiiTABLE OF CONTENTS ivvSUPPLIED ACCESSORIES vQUICK REFERENCE GUIDE IVII n Preparation I n Your first scanning experience III n Memory programming IV n Programmed scan operation V1 PANEL DESCRIPTION 14 n Front, top and side panels 1 n Function display 32 BATTERY CHARGING 58 n Battery installation 5 n Caution 5 n Battery charging 73 FREQUENCY AND CHANNEL SETTING 912 n VFO and memory channels 9 n Frequency band selection 9 n Setting a frequency 11 n Setting a tuning step 11 n Selecting a memory channel 12 n Lock function 124 BASIC OPERATION 1317 n Receiving 13 n Setting audio volume 13 n Squelch level setting 14 n Receive mode selection 14 n Monitor function 15 n Attenuator function 15 n Duplex operation 16 n Dial select step 175 MEMORY CHANNELS 1827 n General description 18 n Selecting a memory channel 18 n Memory channel programming 19 n Memory bank setting 20 n Memory bank selection 21 n Programming memory/bank name 22 n Selecting display type 23 n Copying memory contents 24 n Memory clearing 25 n Transferring memory contents 26 n Erasing/transferring bank contents 276 SCAN OPERATION 2837 n Scan types 28 n Full/band/programmed link/programmed scan 29 n Scan edges programming 30 n Programming scan name 31 n Programming other contents 32 n Memory/all bank/bank link/bank scan 33 n Auto memory write scan 34N Skip channel/frequency setting 35 n Scan resume setting 377 PRIORITY WATCH 3840 n Priority watch types 38 n Priority watch operation 398 TONE SQUELCH AND POCKET BEEP 4144 n Tone squelch frequency/DTCS code setting 41 n Tone/DTCS squelch operation 43 n Tone scan 449 Set mode 4556 n General 45 n Set mode items 4610 OTHER FUNCTIONS 5763 n Antenna selection 57 n function assignment 58 n Auto power-off function 58 n Weather channel operation 59 n Data cloning 61 n Partial reset 63 n All reset 6311 CONTROL COMMAND 6461 n General 64 n Data format 64 n Command table 6512 FREQUENCY TABLE 6774 n TV channels 67 n VHF marine channels 70 n Weather channels 70 n Other communications in the USA 72N Other communications other countries 7313 MAINTENANCE 7576 n Troubleshooting 75 n CP-18A/E fuse replacement 7614 SPECIFICATIONS 7715 OPTIONS 7916 POCKET GUIDE 808117 CE 8182SUPPLIED ACCESSORIESq Antenna 1w Hand strap 1e Belt clip 1r Ni-MH batteries*atteries* 2t AC adapter* 1* Not supplied, or the shape is different, depending on the receiver version.PreparationD Battery installationq Remove the batteryCover from the receiver.w Install two AA (LR6)Size Ni-MH or alkaline cell batteries.
0 kommentar(er)
